Subject to change · 30.30-e · 0215
Page 1
www.argo-hytos.com
D 162 · D 232 · D 332
In-line mounting · Operating pressure up to 63 bar · Nominal flow rate up to 350 l/min
Pressure Filters
Description
Application
In the pressure circuits of hydraulic and lubrication systems.
Performance features
Protection against wear:
By means of filter elements that, in full-flow filtration, meet even
the highest demands regarding cleanliness classes.
Protection against malfunction:
Through installation near to the control valves or other expensive
components. The specific determined flow rate guarantees a
closed by-pass valve even at ν ≤ 200 mm
2
/s
(cold start condition).
Filter elements
Flow direction from outside to centre. The star-shaped pleating
of the filter material results in:
› large filter surfaces
› low pressure drop
› high dirt-holding capacities
› long service life
Filter maintenance
By using a clogging indicator the correct moment for main-
tenance is stated and guarantees the optimum utilization of the
filter life.
Materials
Filter head: Aluminium alloy
Filter bowl: Aluminium alloy
Seals: NBR (FPM on request)
Filter media: EXAPOR
®
MAX 2 - inorganic multi-layer
microfibre web
Paper - cellulose web, impregnated with
resin
Accessories
Electrical and/or optical clogging indicators are available -
optionally with one or two switching points resp. temperature
suppression.
Dimensions and technical data see catalogue sheet 60.30.
Pressure Filter D 232
Page 2
www.argo-hytos.com
Subject to change · 30.30-e · 0215
Characteristics
Operating pressure
0 ... 40 bar, min. 3 x 10
6
pressure cycles
Nominal pressure according to DIN 24550
0 ... 63 bar, min. 10
4
pressure cycles
Quasi-static operating pressure
Permissible pressures for other numbers of cycles
Operating pressure p [bar]
Number of cycles
Nominal flow rate
Up to 350 l/min (see Selection Chart, column 2)
The nominal flow rates indicated by ARGO-HYTOS are based on
the following features:
› closed by-pass valve at ν ≤ 200 mm
2
/s
› element service life > 1000 operating hours at an average fluid
contamination of 0,07 g per l/min flow volume
› flow velocity in the connection lines:
up to 100 bar ≤ 6 m/s
Filter fineness
5 µm(c) ... 30 µm(c)
β-values according to ISO 16889
(see Selection Chart, column 4 and diagram Dx)
Dirt-holding capacity
Values in g test dust ISO MTD according to ISO 16889
(see Selection Chart, column 5)
Hydraulic fluids
Mineral oil and biodegradable fluids
(HEEs and HETG, see info-sheet 00.20).
Temperature range
-30 °C ... +100 °C (temporary -40 °C ... +120 °C)
Viscosity at nominal flow rate
› at operating temperature:ν < 60 mm
2
/s
› as starting viscosity: ν
max
= 1200 mm
2
/s
› at initial operation:
The recommended starting viscosity can be read from the
diagram D (pressure drop as a function of the kinematic
viscosity) as follows: Find the 70 % ∆p of the cracking
pressure of the by-pass valve on the vertical axis. Draw a
horizontal line so that it intersects the ∆p curve at a point.
Read this point on the horizontal axis for the viscosity.
Mounting position
Preferably vertical, filter head on top
Connection
Threaded ports according to ISO 228 or DIN 13. Sizes see Selecti-
on Chart, column 6 (other port threads on request).
Electrical clogging indicator
› Switching voltage: max. 120 V AC / 175 V DC
› Switching current: max. 0,17 A AC / 0,25 A DC
› Switching power: max. 3,5 VA AC / 5 W DC
› Type of contact: Change-over
› Electrical protection: IP 65 (with mounted and secured
socket)
Page 3
www.argo-hytos.com
Subject to change · 30.30-e · 0215
Diagrams
∆p-curves for complete filters in Selection Chart, column 3
D1
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
0
0,5
1,0
1,5
2,0
D 162
1+5
0
3+4
2+6
50 100 150 200 250 300 350 400
∆p [bar]
Q [l/min]
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
2
8
10
4
6
2
1
6
5+6
3+4
5
200 400 600
800
1000
∆p [bar]
ν [mm
2
/s]
D2
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
0
0,5
1,0
1,5
2,0
D 232
1+5
0
3+4
2+6
50 100 150 200 250
300 350
400
∆p [bar]
Q [l/min]
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
2
8
10
4
6
2
1
1
6
3
6
3+4
4
5
5
200 400 600
800
1000
∆p [bar]
ν [mm
2
/s]
D3
Pressure drop as a function of the
flow volume at ν = 35 mm
2
/s (0 = casing empty)
0
0,5
1,0
1,5
2,0
D 332
1+5
0
3+4
2+6
50 100 150 200 250 300 350 400
∆p [bar]
Q [l/min]
Pressure drop as a function of the
kinematic viscosity at nominal flow
0
2
8
10
4
6
2
2
1
3
4
6
5
5
3+4
1+2
200 400 600
800
1000
∆p [bar]
ν [mm
2
/s]
Page 4
www.argo-hytos.com
Subject to change · 30.30-e · 0215
Dx
Filter fineness curves in Selection Chart, column 4
Filtration ratio β as a function of particle size x obtained
by the Multi-Pass-Test according to ISO 16889
The abbreviations represent the following β-values resp.
finenesses:
For EXAPOR
®
MAX2 and Paper elements:
5EX2 = β
5 (c)
= 200 EXAPOR
®
MAX 2
7EX2 = β
7 (c)
= 200 EXAPOR
®
MAX 2
10EX2 = β
10 (c)
= 200 EXAPOR
®
MAX 2
16EX2 = β
16 (c)
= 200 EXAPOR
®
MAX 2
30P = β
30 (c)
= 200 Paper
Based on the structure of the filter media of the 30P paper
elements, deviations from the printed curves are quite probable.
For special applications, finenesses differing from these curves
are also available by using special composed filter material.
Filtration ratio β for particles> x µm
Particle size x [µm] (for particles larger
than the given particle size x)
Efficiency [%]
Order Information
Optical or electrical indicators are available to monitor the clogging condition of the element. If the indicator should be already
mounted onto the filter head use the abbreviation “M” behind the part number of the indicator. The printed order acknowledge-
ments show both items separately.
Order example: The Filter D 232-256 has to be supplied with optical clogging indicator - response pressure 2,0 bar.
Order description: D 232-256 / DG 042-01 M
Part No. (basic unit) Mounted
Clogging indicator
For the appropriate clogging indicator see catalogue sheet 60.30.
Besides these mounted clogging indicators we also offer - with a certain order quantity - clogging indicators integrated in the
filter head (as listed under „dimensions“).
Order examples:
D 232-256 ED (electrical differential pressure switch) the switching pressure matches the
D 232-256 OD (optical differential pressure indicator) cracking pressure of the by-pass valve
Remarks:
› The switching pressure of the clogging indicator has always to be lower than the cracking pressure of the by-pass valve
(see Selection Chart, column 7).
› The filters listed in this chart are standard filters. Other designs available on request.
}
Page 5
www.argo-hytos.com
Subject to change · 30.30-e · 0215
Selection Chart
Part No.
Nominal flow rate
Pressure drop see
diagram
D/
curve no.
Filter fineness see diagr.
Dx
Dirt-holding capacity
Connection A/B
Cracking pressure of by-pass
Symbol
Replacement filter element
Part No.
Weight
Clogging indicator
Remarks
l/min g bar kg
1 2 3 4 5 6 7 8 9 10 11 12
D 162-253 85 D1/1 5EX2 24 G1¼ 3,5 4 V3.0817-03 2,4 optional -
D 162-256 140 D1/2 10EX2 33 G1¼ 3,5 4 V3.0817-06 2,4 optional -
D 162-258 200 D1/3 16EX2 33 G1¼ 3,5 4 V3.0817-08 2,4 optional -
D 162-251 220 D1/4 30P 18 G1¼ 3,5 4 P3.0817-01* 2,4 optional -
D 162-283 160 D1/5 5EX2 24 G1¼ 7 4 V3.0817-03 2,4 optional -
D 162-286 250 D1/6 10EX2 33 G1¼ 7 4 V3.0817-06 2,4 optional -
D 232-253 120 D2/1 5EX2 33 G1¼ 3,5 4 V3.0823-03 3,4 optional -
D 232-256 195 D2/2 10EX2 47 G1¼ 3,5 4 V3.0823-06 3,4 optional -
D 232-258 275 D2/3 16EX2 48 G1¼ 3,5 4 V3.0823-08 3,4 optional -
D 232-251 280 D2/4 30P 26 G1¼ 3,5 4 P3.0823-01* 3,4 optional -
D 232-283 220 D2/5 5EX2 33 G1¼ 7 4 V3.0823-03 3,4 optional -
D 232-286 300 D2/6 10EX2 47 G1½ 7 4 V3.0823-06 3,4 optional -
D 332-253 170 D3/1 5EX2 49 G1¼ 3,5 4 V3.0833-03 4,0 optional -
D 332-256 275 D3/2 10EX2 67 G1¼ 3,5 4 V3.0833-06 4,0 optional -
D 332-258 280 D3/3 16EX2 68 G1¼ 3,5 4 V3.0833-08 4,0 optional -
D 332-251 350 D3/4 30P 34 G1½ 3,5 4 P3.0833-01* 4,0 optional -
D 332-283 280 D3/5 5EX2 49 G1¼ 7 4 V3.0833-03 4,0 optional -
D 332-286 350 D3/6 10EX2 67 G1½ 7 4 V3.0833-06 4,0 optional -
* Paper media supported with metal gauze
Page 6
www.argo-hytos.com
Subject to change · 30.30-e · 0215
Dimensions
Terminal-
connection
Measurements
Type A/B C D E F G H I K
AF
L M
Ø/depth
N O P Q R S T
D 162 G1¼ 61 232 38 62 140 95 80 32 80 M12/18 116 AF 60 34 17 115 34 66
D 232 G1¼, G1½ 61 296 38 62 140 95 80 32 80 M12/18 116 AF 60 34 17 115 34 66
D 332 G1¼, G1½ 61 396 38 62 140 101 80 32 80 M12/18 116 AF 60 34 17 115 34 66
Type U V W X
ED OD
D 162 66 44 30 49 30
D 232 66 44 30 49 30
D 332 66 44 30 49 30
Symbols
1 2 3 4 5 6 7
P
1
P
2
P
1
P
2
Clogging indicator optional:
Pressure holes plugged with screws M4
Version with electrical
clogging indicator DG 041
Version OD
with integrated optical clogging
indicator
Minimum distance
from ferromagnetic
parts: 7 mm
Version ED
with integrated electrical
clogging indicator
Minimum distance
from ferromagnetic
parts: 7 mm
Page 7
www.argo-hytos.com
Subject to change · 30.30-e · 0215
Spare Parts
6
7
9
8
3
2
1
5
4
Pos. Designation Part No.
1 Filter bowl D 162 D 162.0102
1 Filter bowl D 232 D 232.0102
1 Filter bowl D 332 D 332.0102
2 O-ring 88,57 x 2,62 N007.0886
3 Filter element (with seal) see Chart / col. 9
4 Hexagonal head screw M4 x 8
DIN 933-8.8
11385800
5 Bonded seal 4,1 x 7,2 x 1 12504600
6 Reed switch with screws and
socket (Pos. 7)
HD 049.1410
7 Socket DIN 43650 - AF3 DG 041.1220
8 Optical clogging indicator
(with Pos. 9)
D 232.1400
9 O-ring 12,3 x 2,4 N007.0124
The functions of the complete filters as well as the outstanding
features of the filter elements assured by ARGO-HYTOS can
only be guaranteed if original ARGO-HYTOS spare parts are
used.
Quality Assurance
Quality management according to DIN EN ISO 9001
To ensure constant quality in production and operation, ARGO-HYTOS filter elements undergo strict controls and tests according to
the following ISO standards:
ISO 2941 Verification of collapse/burst pressure rating
ISO 2942 Verification of fabrication integrity (Bubble Point Test)
ISO 2943 Verification of material compatibility with fluids
ISO 3968 Evaluation of pressure drop versus flow characteristics
ISO 16889 Multi-Pass-Test (evaluation of filter fineness and dirt-holding capacity)
ISO 23181 Determination of resistance to flow fatigue using high viscosity fluid
Before release into the series production the filter casing is tested for fatigue strength in our pressure pulse test rig.
Various quality controls during the production process guarantee the leakfree function and solidity of our filters.
Illustrations may sometimes differ from the original. ARGO-HYTOS is not responsible for any unintentional mistake in this specification sheet.